Ecmweb 20595 Nec Code Quandaries July 2018 Pr 0
Ecmweb 20595 Nec Code Quandaries July 2018 Pr 0
Ecmweb 20595 Nec Code Quandaries July 2018 Pr 0
Ecmweb 20595 Nec Code Quandaries July 2018 Pr 0
Ecmweb 20595 Nec Code Quandaries July 2018 Pr 0

Stumped by the Code? Requirements When Installing Type MC Cable

July 16, 2018
NEC Requirements When Installing Type MC Cable

All questions and answers are based on the 2017 NEC.

Underline text indicates a Code change.

Q. What are the Code requirements when installing Type MC cable in accessible attics or roof spaces?

A. Type MC cable installed in accessible attics or roof spaces must comply with Sec. 320.23 [330.23].

On the surface of floor joists, rafters, or studs. In attics and roof spaces that are accessible, substantial guards must protect cables installed across the top of floor joists, or across the face of rafters or studding within 7 ft of the floor or floor joists. If this space isn’t accessible by permanent stairs or ladders, protection is required only within 6 ft of the nearest edge of the scuttle hole or attic entrance [Sec. 320.23(A)].

Along the side of framing members [320.23(B)]. When Type MC cable is installed on the side of rafters, studs, or floor joists, no protection is required if the cable is installed and supported so the nearest outside surface of the cable or raceway is at least 1¼ in. from the nearest edge of the framing member where nails or screws are likely to penetrate [Sec. 300.4(D)].

Q. What are the uses not permitted by the NEC for Type NM cable?

A. Types NM and NMC cables aren’t permitted [Sec. 334.12(A)]:

(1) In any dwelling or structure not specifically permitted in 334.10(1), (2), (3), and (5).

(2) Exposed within a dropped or suspended ceiling cavity in other than one‑ and two‑family, and multifamily dwellings (Figure).

(3) As service‑entrance cable.

(4) In commercial garages having hazardous locations, as defined in Sec. 511.3.

(5) In theaters and similar locations, except where permitted in 518.4(B).

(6) In motion picture studios.

(7) In storage battery rooms.

(8) In hoistways, or on elevators or escalators.

(9) Embedded in poured cement, concrete, or aggregate.

(10) In any hazardous location, except where permitted by other sections in the Code.

In addition, Type NM cables aren’t permitted to be used under the following conditions, or in the following locations [Sec. 334.12(B)]:

(1) If exposed to corrosive fumes or vapors.

(2) If embedded in masonry, concrete, adobe, fill, or plaster.

(3) In a shallow chase in masonry, concrete, or adobe and covered with plaster, adobe, or similar finish.

(4) In wet or damp locations.  

Note: A raceway in a ground floor slab is considered a wet location.

Q. What are the Code requirements for Type MC cable to serve as an equipment grounding conductor (EGC)?

A. If Type MC cable is to serve as an EGC, then it must comply with Sec. 250.118(10) and Sec. 250.122 [330.108].

The outer sheath of traditional interlocked Type MC cable isn’t permitted to serve as an EGC; therefore, this cable must contain an EGC in accordance with Sec. 250.118(1) [250.118(10)a].

The outer sheath of interlocked Type MCAP cable containing an aluminum grounding/bonding conductor running just below the metal armor is listed to serve as an EGC [Sec. 250.118(10)(b)].

The outer sheath of smooth or corrugated-tube Type MC cable is listed to serve as an EGC [Sec. 250.118(10)(c)].                    

About the Author

Mike Holt

Mike Holt is the owner of Mike Holt Enterprises (www.MikeHolt.com), one of the largest electrical publishers in the United States. He earned a master's degree in the Business Administration Program (MBA) from the University of Miami. He earned his reputation as a National Electrical Code (NEC) expert by working his way up through the electrical trade. Formally a construction editor for two different trade publications, Mike started his career as an apprentice electrician and eventually became a master electrician, an electrical inspector, a contractor, and an educator. Mike has taught more than 1,000 classes on 30 different electrical-related subjects — ranging from alarm installations to exam preparation and voltage drop calculations. He continues to produce seminars, videos, books, and online training for the trade as well as contribute monthly Code content to EC&M magazine.

Voice your opinion!

To join the conversation, and become an exclusive member of EC&M, create an account today!

Sponsored Recommendations

Electrical Conduit Comparison Chart

CHAMPION FIBERGLASS electrical conduit is a lightweight, durable option that provides lasting savings when compared to other materials. Compare electrical conduit types including...

Fiberglass Electrical Conduit Chemical Resistance Chart

This information is provided solely as a guide since it is impossible to anticipate all individual site conditions. For specific applications which are not covered in this guide...

Considerations for Direct Burial Conduit

Installation type plays a key role in the type of conduit selected for electrical systems in industrial construction projects. Above ground, below ground, direct buried, encased...

How to Calculate Labor Costs

Most important to accurately estimating labor costs is knowing the approximate hours required for project completion. Learn how to calculate electrical labor cost.